Multitech CDMA Spécifications Page 21
- Page / 129
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 6 – Global Configuration Commands
Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide 21
Restore Factory Settings &F
Description: This command is used to restore the factory settings from NV memory. This is a standard Hayes®
modem AT command.
See Appendix "Effects of AT&W, ATZ and AT&F
Note: There is a remote chance of NV memory corruption if a reset or power loss
occurs during the processing of this command. Only use this command during
the initial setup of the operating characteristics.
Syntax: AT&F
Command
Possible Responses
AT&F
OK
Note: Command valid, modem resets
Save Configuration &W
Description: This command writes the current configuration to NV. See table in Chapter 20 for a list of items.
This is a standard Hayes® modem AT command.
Syntax: AT&W
Command
Possible Responses
AT&W
OK
Note: Command valid
Reset to Default Configuration Z0
Description: This command is used to restore the configuration last saved by AT&W.
Syntax: ATZ0
Command
Possible Responses
ATZ0
Note: reset to default
configuration.
OK
Note: Command is valid
- CDMA-C1 AT Commands 1
- Copyright 2
- Trademarks 2
- Revisions 2
- Contacting Multi-Tech 2
- Contents 3
- Contents 4
- Document Scope 9
- Related References 9
- Serial Interface Settings 10
- Overview 10
- Terminology 11
- Command Format and Syntax 11
- Command-Line Editing 12
- Input Command Syntax 12
- Other Syntax 12
- Output Response Syntax 12
- Parameter Defaults 13
- Unsolicited Message Syntax 13
- Attention AT 14
- Repeat Last Command A/ 14
- Echo E 14
- +WUSLMSK 15
- Syntax: AT+WPRI? 16
- Hardware Version +WHWV 17
- Capabilities List +GCAP 19
- Subscriber Number +CNUM 19
- Save Configuration &W 21
- General Indicator +WIND 22
- Result 23
- Examples: +WIND: 4 23
- Error Codes: 24
- Chapter 7 – Status Commands 25
- Fixed DTE Rate +IPR 28
- Set DCD Signal &C 29
- Set DTR Signal &D 29
- Set DSR Signal &S 30
- Syntax: AT+DR=<val> 31
- Syntax: AT+WCHD 31
- Automatic Answer S0 32
- Command Edit Character S5 33
- Dial Command D 35
- Hang-Up Command H 36
- Answer a Call A 36
- Syntax: ATA 37
- Incoming Call +RING 38
- Emergency Mode +WSOS 40
- Call Answered +WANS 41
- Call Connected +WCNT 41
- Call Ended +WEND 42
- Call Originated +WORG 43
- CPHS Command +CPHS 43
- Values: <LineId> 44
- Examples: 44
- Call Forwarding +CCFC 45
- Syntax: AT+WFSH 46
- Unsolicited 46
- Send DTMF Tones +VTS 47
- Serving System +CSS 49
- Signal Quality +CSQ 50
- Band Preference +WBND 53
- Service Indication +WSRV 53
- Roam Preference +WRMP 54
- Default Cell Band +WDCB 55
- Roaming Indication +WROM 55
- Values: <indicator> 56
- Values: <mode> 58
- Excess SPC Failures +WLCK 60
- Commit Changes +WCMT 61
- Set IMSI +WIMI 62
- SID and NID +WSID 63
- Commit Successful +WOTC 66
- SPL Unlocked +WOTS 66
- NAM Download OK +WOTN 66
- MDM Download OK +WOTM 67
- IMSI Download OK +WOTI 67
- PRL Download OK +WOTP 67
- Values: <Mode> 74
- Parameter 74
- Send Message +CMGS 75
- Read Message +CMGR 76
- List Message +CMGL 77
- Delete Message +CMGD 79
- Syntax: +WMGF 84
- Audio Subsystem Overview 85
- Chapter 15 – Audio Commands 86
- Microphone Gain +VGT 87
- Speaker Gain Control +VGR 88
- Values: <Gain> 89
- Digital Gain Receive +WDGR 90
- Values: <val1> 91
- Echo Cancellation +ECHO 92
- Audio Loopback &T 94
- Quick Net Connect $QCQNC 95
- R-SCH Selection $QCMIP 96
- MIP Selection $QCMIPP 96
- Chapter 16 – Data Commands 97
- Configure TCP/IP +WIPCFG 99
- Values: <cmdtype> 101
- Bearer Status +WIPBR 102
- Values: <protocol> 103
- Response 105
- Syntax: AT+WIPERR? 105
- Values: 107
- Options and 107
- 32kHz Sleep Mode +W32K 110
- Chapter 18 – Sleep Commands 111
- Syntax: +WNETTIMEGET? 112
- Response Field 112
- Description: 112
- Introduction 113
- Acquiring Cellular Service 113
- Call Processing 114
- Sending Binary Data 115
- TCP Socket Examples 116
- TCP Client Socket Connection 117
- TCP Server Example 117
Produits connexes et manuels pour Mise en réseau Multitech CDMA
Mise en réseau Multitech MT2834BL Spécifications
(225 pages)
(225 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels