Multitech MTCBA-C-U Spécifications Page 154
- Page / 197
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 19 – Reference Information
Multi-Tech Systems, Inc. CDMA AT Commands Reference Guide (PN S000294K) 154
MuxLite Example
The following provides a usage example for the MuxLite feature. It assumes that the module data port is connected to COM1
and the module diagnostic port is connected to COM2. Though individual AT commands are shown in this example, HDLC
packet encoding/decoding must be performed on all diagnostic port (COM2) commands and responses as described in the
MuxLite application note [13].
COM1:
AT+CMEE=1 Enable detailed reporting of mobile equipment errors.
OK
…Host configured… Host application configured for PPP dial up access.
ATD#777 Initiate a data call. Number string is carrier specific.
CONNECT Data call connected.
…PPP negotiation… PPP layer startup and data exchange.
COM2:
AT+CLCC Display current call state.
+CLCC: 1,1,0 Active data call.
OK
WROM: 1 Unsolicited response, roaming status has changed.
AT+CSQ? Display signal quality and frame error rate.
+CSQ: 27,99
OK
AT+CNMI=2,2,0,0,0 Set SMS message reception procedure; acknowledge using +CNMA
OK
AT+CPMS=”MT” Set “Mobile Terminated” as preferred SMS memory storage
OK
…
+CMT:"8585551212","02/05/17,10 :43 :07",129,1,2,0,”5550000”,0
Unsolicited response, SMS message received.
AT+CNMA Acknowledge received SMS message to the network.
OK
AT+CMGR=0 Read the SMS message.
+CMGR:"REC UNREAD","8585552222","02/05/15,15 :54 :04",1,2,0,”5550000”,15
Don, give me a call. Kathy
OK
AT+CMGS=”8585551212” Send a SMS message (part in a separate HDLC packet)
I’ll be home in 5 minutes. Message text (part in a separate HDLC packet)
OK
…
+CMGS: 1 Message accepted by SMS Service Center
…
+CDS:2,1,"8582431439",129,"02/05/17,10 :14 :17","02/05/17,10 :14 :27",32768
Message delivery report.
COM1:
…PPP layer shutdown… Host application terminates PPP session
NO CARRIER Data call terminated
AT Module re-enters command mode
OK
COM2:
AT+CSQ? Display signal quality and frame error rate.
+CME ERROR: 3 Error returned from module.
AT+CLCC Display current call state.
+CLCC: 0,9,0 Error return cause; module not in an active data call.
OK
- CDMA AT Commands 1
- Contents 3
- Chapter 1 – Introduction 9
- Terminology and Acronyms 10
- Chapter 2 – AT Command 13
- Features 13
- Attention AT 14
- Request IMSI +CIMI 15
- Capabilities List +GCAP 15
- Repeat Last Command A/ 15
- Phone Offline +CPOF 16
- Keypad Control +CKPD 17
- Clock Management +CCLK 17
- Ring Melody Playback +CRMP 17
- Ringer Sound Level +CRSL 18
- Subscriber Number +CNUM 18
- View Modem Timers +WTMR 19
- Chapter 4 – Call Control 20
- Hang-Up Command H 21
- Answer a Call A 22
- Remote Disconnection 22
- DTMF Signals +VTD, +VTS 23
- Automatic Answer S0 24
- Incoming Call Bearer +CICB 25
- Microphone Gain +VGT 26
- Volume Gain Control +VGR 26
- Echo Cancellation +ECHO 27
- TTY Mode +WTTY 28
- Chapter 5 – Network Service 29
- Band Preference +WBND 30
- Roam Preference +WRMP 31
- Change NAM Selection +WNAM 32
- Read Current NAM +WCNM 32
- Chapter 6 – SIM Card 35
- Operational Commands 35
- Enter PIN2 +CPIN2 36
- Change Password +CPWD 38
- Card Identification +CCID 38
- Chapter 7 – Short Messages 39
- Delete Message +CMGD 47
- Message Overwriting +WMGO 49
- Change SMS Status +WUSS 49
- Chapter 8 – Supplementary 51
- Services Commands 51
- Chapter 9 – Data Commands 55
- Cellular Result Codes +CRC 56
- Chapter 10 – V.24-V.25 58
- Set DCD Signal &C 59
- Set DTR Signal &D 60
- Set DSR Signal &S 60
- Back to Online Mode O 60
- Result Code Suppression Q 60
- DCE Response Format V 61
- Audio Loopback &T 61
- Echo E 61
- Save Configuration &W 62
- Chapter 11 – Phone Book 63
- Phonebook Read +CPBR 66
- Phonebook Search +CPBP 66
- Chapter 12 – Position 68
- Determination (GPS) 68
- IP Server Address +WMPC 73
- Chapter 13 - Specific AT 74
- Read GPIO Value +WIOR 78
- Write GPIO Value +WIOW 78
- Play Tone +WTONE 78
- Play DTMF Tone +WDTMF 79
- Hardware Version +WHWV 79
- Select Voice Gain +WSVG 80
- Status Request +WSTR 80
- Ring Indicator Mode +WRIM 81
- 32kHz Sleep Mode +W32K 81
- Software Version +WSSW 82
- CPHS Command +CPHS 83
- Reset +WRST 84
- Set Standard Tone +WSST 85
- Security PIN +WPIN 86
- Minute Alert +WMBP 87
- Chapter 14 - SIM ToolKit for 89
- RUIM Software Version 89
- Example: 91
- Chapter 15 – Provisioning AT 99
- Set IMSI +WIMI 100
- SID and NID +WSID 101
- Slot Cycle Index +WSCI 101
- Packet Dial String +WPDS 102
- Commit Changes +WCMT 104
- Read SID/NID Entries +WSNR 104
- Download PRL +DPRL 105
- Service Programming Example 106
- Chapter 16 – Extended AT 107
- Commands in IS707.3 107
- Select Pulse Dialing P 108
- Basic S-Registers S 108
- Error Control Report +ER 109
- Modulation Selection +MS 113
- V.18 Selection +MV18S 114
- Cellular Extension +CXT 115
- Configuration String +CFG 115
- Query Service +CAD 115
- Battery Charge +CBC 117
- Serving System +CSS 118
- Hang-up Voice +CHV 119
- Chapter 17 – Qualcomm 121
- Defined AT Commands for 121
- CDMA Operation 121
- Set DM Baud Rate $QCDMR 125
- SCRM’ing Selection $QCSCRM 126
- R-SCH IP Selection $QCMIP 127
- MIP Selection $QCMIPP 128
- Chapter 18 – TCP/IP App AT 133
- Commands 133
- Open Socket +WOSK 134
- Close Socket +WCSK 135
- Transmit Socket Data +WSTX 135
- Read Receive Data +WSRX 136
- Force Dormant Mode +WFDM 138
- IP Address Lookup +WDNS 139
- Display IP Address +WIPC 139
- PPP Session Status +WPPP 139
- Socket State Change +WSKS 140
- Received Socket Data +WSRX 141
- Socket Data Error +WSRE 141
- Chapter 19 – Reference 143
- Information 143
- Specific Error Result Codes 144
- Final Result Codes 145
- Intermediate Result Codes 145
- Parameters Storage 147
- TCP App Socket Status Events 150
- TCP App Socket Error Codes 150
- TCP App DNS Server Codes 150
- TCP App PPP Network Codes 150
- Phonebook UCS2 Unicode 152
- MuxLite Example 154
- Chapter 20 – Unsolicited AT 155
- Result Codes 155
- Key Press or Release +CKEV 156
- Mode Preference +COPS 158
- Incoming Call +CRING 158
- RxLev Indication +CSQ 159
- Incoming Call +RING 159
- Call Answered +WANS 159
- Call Connected +WCNT 160
- Call Ended +WEND 160
- Flash Indication +WFSH 161
- General Indicator +WIND 161
- Call Originated +WORG 162
- Roaming Indication +WROM 162
- Emergency Mode +WSOS 163
- Current NAM Change +WNAM 163
- Voice Mail Indicator +WVMI 164
- Power Save +WSPS 164
- Download PRL Status +DPRL 167
- Chapter 21 – AT Command 168
- Examples 168
- Incoming Voice Call 169
- Call Waiting 169
- Originate Data Call 169
- Originate Data Call Failure 169
- Short Message Examples 170
- GpsOne Examples 171
- AT Commands 175
- Read Message +CMGR 177
- List Message +CMGL 178
- Send Message +CMGS 179
- Facility Lock +CLCK 185
- Signal Quality +CSQ 185
- Boot URL +WBURL 187
- Trusted Domain +WTDMN 187
- Proxy Address +WDPXY 187
- IOTA Error +WOAE 188
- Please Retry +WOAR 188
- Display PRI Checksum +WSUM 189
Produits connexes et manuels pour Mise en réseau Multitech MTCBA-C-U
(29 pages)
(10 pages)
(58 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels