Multitech IPC-623C Guide de l'utilisateur Page 39
- Page / 87
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Software Configuration
CommPlete 4000 Server SBC, Model IPC-623C 39
TYPE button. Click the CHANGE button in the “Adapter
Type” area.
(4). Push the “HAVE DISK BUTTON” and press OK.
(5). Specify the path for the new driver and press the <Enter>
key. The “Select Device” dialog box will appear. Select the
“Chips and Tech 69000 PCI”.
(6). Follow the remaining instruction that appear on the screen
to complete the rest of the installation, then restart your
computer.
3. Install VGA driver to Windows NT 3.5x/4.0
(1). To install VGA drivers to Windows 3.5x/4.0 is as you
normally would. Click START, then SETTINGS, then
CONTROL PANEL of the operating system.
(2). Select the DISPLAY icon to start the DISPLAY
PROPERTIES window, then choose the SETTING tab, then
DISPLAY TYPE.
(3). In the CHANGE DISPLAY TYPE window, click on the
CHANGE button in the ADAPTER TYPE, this will bring up
the SELECT DEVICE window.
(4). In the CHANGE DISPLAY window, click on Have Disk.
Follow the instructions appearing on the screen until you
complete the whole installation.
(5). Once installation is completed, the system must be shut
down and restarted for the new drivers to take effect.
4. Install VGA driver to OS/2 Warp Operation System
(1) Preliminary Steps:
(i) OS/2 DOS Support must be installed.
(ii) If you previously installed SVGA support, you must reset
the system to VGA mode. VGA is the default video mode
enable when OS/2 is to be installed.
(iii) To restore VGA mode, Use SELECTIVE INSTALL and
select VGA for PRIMARY DISPLAY. For more
information on this procedure, see the section on
Changing Display Adapter Support in the OS/2 User’s
Guide.
- User Guide 1
- S000277A Revision A 2
- Contents 3
- Table of Contents 4
- Chapter 1 - Introduction 5
- Chapter 4 Green PC Function 6
- Chapter 5 Award BIOS Setup 6
- Appendix A Expansion Bus 6
- Appendix B Technical Summary 6
- Appendix C Troubleshooting 6
- 1-2 System Specifications 7
- Introduction 8
- 1-3 Safety Precautions 10
- Chapter 2 - Hardware 11
- Configuration 11
- 2-2 Component Locations 12
- Pin Jumper 13
- 3 Pin Jumper 13
- Jumper Block 13
- Jumper Cap 13
- Jumper Diagrams 14
- Jumper Settings 14
- 2-4 COM Port Connector 15
- Hardware Configuration 16
- 2-6 IRQ12 Release Selection 18
- PIN SIGNAL FUNCTION 19
- 1 Pull Low 19
- 2 PWR BTN Switch 19
- 2-11 Solid-State Disk Socket 21
- 2-12 SSD Memory Map Selection 22
- 2-16 Reset Connector 24
- 2-18 CPU Fan Connector 25
- 2-19 System Fan Connector 26
- 2-23 VGA CRT Connector 30
- 2-24 LCD Panel Connector 31
- 1 LCD+12V 32
- 3 LCD VDD (+5V/3.3V) 32
- 2-27 Printer Connector 33
- 2-29 LAN Connector 34
- 1 EXTSMI 35
- 2-32. Memory Installation 36
- Chapter 3 - Software 37
- 3-2. VGA Driver Utility 38
- Software Configuration 39
- 3-3. Flash BIOS Update 41
- FLASH MEMORY WRITER v7.XX 42
- F1: Reset F10: Exit 42
- 3-4. LAN Driver Utility 43
- Chapter 4 - Green PC 46
- Function 46
- 4-2. CPU Doze Mode 47
- 4-3. System Standby Mode 47
- 4-4 System Suspend Mode 47
- Chapter 5 - Award BIOS 48
- Setup 48
- 5-2 Entering Setup 49
- Award BIOS Setup 50
- ROM PCI / ISA BIOS (2A69KP6C) 51
- STANDARD CMOS SETUP 51
- AWARD SOFTWARE, INC 51
- Size (Capacity): 54
- Drive A and Drive B: 54
- Halt On: 54
- Hard Disk Attributes: 55
- Virus Warning 56
- Typematic Rate Setting 58
- Typematic Rate (Chars/Sec) 58
- Typematic Delay (Msec) 58
- Security Option 58
- PCI/VGA Palette Snoop 58
- OS SELECT FOR DRAM>64MB 59
- Report No FDD for Win 95 59
- Video BIOS Shadow 59
- CMOS Setup 60
- Utilities 60
- 5-6 Power Management Setup 64
- 5-7 PnP/PCI Configuration 67
- 5-8 Load BIOS Defaults 69
- 5-9 Load Setup Defaults 69
- 5-10 Integrated Peripherals 70
- Onboard UART 2 Mode 72
- Onboard Parallel Port 72
- Parallel Port Mode 72
- 5-11 Password Setting 73
- 5-12 IDE HDD Auto Detection 74
- 5-14 Save & Exit Setup 75
- Appendix A - Expansion 77
- Appendix A: Expansion Bus 78
- ISA Bus Pin Assignments 79
- PCI Bus Pin Assignments 80
- Appendix B - Technical 81
- Appendix B: Technical Summary 82
- Appendix C 85
- Troubleshooting 85
- Appendix C: Troubleshooting 86
Produits connexes et manuels pour Manuels des logiciels Multitech IPC-623C
(81 pages)MaxxAir BF24TFORGPRO Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Nein MaxxAir BF24TFORGPRO.
Wir stellen 1 PDF-Handbücher MaxxAir BF24TFORGPRO zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Gebrauchs- und Pflegehandbuch
Commentaires sur ces manuels